Vehicles
Sections
171 not categorized PORSCHE 996 EXHAUST FORCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 928 1987-91 (includes uncategorized and accessory items) FVDMK964400 Simplify your exhaust installation with one of our pre-packaged installation kits. Each kit is sourced in Germany and includes new installation hardware. Sold as a kit. 1 necessary per car.
$19.40
Make a selection
$244.19
Make a selection FVD11196415GKT This installation kit is needed to install our part numbers FVD 111 964 15 or FVD 111 964 17. Sold as a set. 1 necessary per car.
$42.90
Make a selection RESMK911001 This kit is necessary when installing any of our racing / street exhaust systems manufactured by m&m exhaust gmbh whose part number begins with res 911 or bes 911 kit contains: - modified oil lines - straps - header / heat exchanger gaskets
$378.81
Make a selection
$228.80
Make a selection
$36.85
Make a selection
$809.46
Make a selection FVD111LAMVER Having problems with your check engine light? Want to run cat bypass pipes or a free flowing sports catalyst set up on your vehicle without having to reprogram the dme (ecu)? This adapter offsets the oxygen sensor about 1.5 inch from the gas stream. This achieves, in most cases, a sufficient measurement for the air/co ratio and increases the tolerance range between the pre and post cat oxygen sensors. In addition, the sensitivity of the oxygen sensor is also reduced allowing you to run a nearly any exhaust or catalytic set up, including bypass pipes, without the need to reprogram your ecu! Use only for the 2nd oxygen sensor (after catalytic)! General FitmentBOXSTER 1997-04911 GT3 2007-11 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05 911 1989-94 911 1987-89 911 1984-86 911 1978-83 CAYENNE 2007-10 CAYENNE 2003-06 CAYMAN 2006-08 BOXSTER 2005-08 968 1992-95 944 1982-85 944 1985-88 944 1989-91 928 1992-95 928 1987-91 928 1983-86 924 1986-88 924 1980-85 911 1994-98
$42.90
Make a selection BES98215000S2 The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$2,816.00
Make a selection BES987C0200SHD Brombacher Cayman/s (sound version) stainless steel exhaust system facts: - + 20 crank hp & + 19 crank torque - 200 cell high flow, tri metal German hjs sport catalysts - 2 tubing (50 mm) straight through design for max. Power - weighs 57 lbs. (25,8 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability - dual 3.5 (90mm) round tips - includes quick release clamps - made in Germany - intoxicating growl at idle, partial throttle and wide open throttle - no dme programming necessary. FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredibl...(choose a part on the right to read more)
$8,541.03
Make a selection BES99110200SK "brombacher" stainless steel exhaust system with valves for the 991 + 25 hp & + 20 tq gain. - 200 cell hjs "hd" sport catalysts. - 25 lb. Weight savings over OEM system (weighs 59 lbs. (27,0 kg), OEM weighs 84 lbs. (38kg). - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - motorsport merge collector. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - "aero quip" style motorsport connections without gaskets or flanges to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - under load (moving) with valves closed: 85db* - under load (movin...(choose a part on the right to read more)
$10,030.90
Make a selection BES99110200SK1 "brombacher" stainless steel sound switch exhaust system complete for the 991 3,4l. + 25 hp & + 20 tq gain. - 200 cell hjs "hd" sport catalysts. - 25 lb. Weight savings over OEM system (weighs 59 lbs. (27,0 kg), OEM weighs 84 lbs. (38kg). - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - motorsport merge collector. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport connections without gaskets or flanges to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. Please note: the 991 Carrera s (us or canadian model) comes standard with valves! Power...(choose a part on the right to read more)
$9,556.80
Make a selection BES99107060S The perfect addition for an aggressive exhaust note with the added benefit of reduced weight. Features: 2 1/2 (63.5mm) tubing. Weighs 8.3 lbs. (3,7 kg), 10 + lbs. Savings over stock GT3 center muffler. Made of German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. Fits 991.1 and 991.2 GT3 & GT3 rs models.- reuse's factory tips. Includes all necessary clamps and mounting brackets. Made in Germany by m&m exhaust, gmbh. Intoxicating growl at idle, partial throttle and wide-open throttle. No interior resonance or drone. Ecu software is not necessary. Does not alter emissions, 50 state legal in the u.s. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany. T...(choose a part on the right to read more)
$2,313.30
Make a selection BES99729200SHD For 997-2 with OEM or valved Porsche sport exhaust (pse). Facts: - equal length headers with long tube design - 200 cell hd German hjs tri metal sport cats - 2.5 tubing (63.5 mm) - made in Germany power: - 997.2 (3,6l) = + 20 crank hp (15 kw) & + 15 crank torque (20 nm) - 997.2s (3,8l) = + 23 crank hp (18kw) & 22 crank torque (30nm) - with FVD flashclient software = + 37 crank hp (28kw) & + 30 crank torque (40 nm) our latest development for the 997.2 is aimed at those who are looking for more torque in the mid range, a rich, deep exhaust growl. These headers contain the latest hjs cats, they are nicknamed "hd" for high durability matrix design catalytic converters. They have a sm-matrix (winding of three flat...(choose a part on the right to read more)
$5,036.90
Make a selection BK7033 Re-issue of autobooks manual covering engine, fuel & cooling systems, ignition, heating, exhaust emissions, clutch, transmission, rear axle, suspension, steering gear, brakes, electronics, and bodywork. This is a manual that will help keep 912 on the road. A must for any 912 owner. General FitmentACCESSORY
$32.00
Make a selection BES99105060S - + 12 crank hp & + 12 crank torque - 2 3/4 tubing (70mm) straight through design for max. Power - weighs 18 lbs. (8.5 kg), which is a 3 lbs. Savings off of OEM center muffler. - replaces stock side mufflers and stock center muffler. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 2 x 3.5 (90mm) round tips. - includes all necessary clamps and mounting brackets. - made in Germany. - intoxicating cup car growl at idle, partial throttle and wide open throttle. - no dme programming necessary, does not alter emissions, 50 state legal in the u.s. Our 991 GT3 center muffler replacements are vastly different than the baffle plated mufflers stuffed with packing that are common in the after...(choose a part on the right to read more)
$2,337.50
Make a selection BES99725241SK "brombacher" edition valved mufflers are the perfect compromise for you and your loved ones. Rich, deep race car tones with the valves open and soft subtle, completely stock sounds with them closed. - + 25 crank hp & + 19 crank torque - 200 cell high flow, tri metal German hjs sport catalysts - 2 3/4 tubing (70mm) straight through design for max. Power - weighs 55 lbs. (25,0 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability - 85 db at idle and partial rpms(up to 60 mph) with valves closed, 100 db at wide open throttle with valves open. - cone style catalytic connection design to prevent exhaust leaks - includes quick release clamps - made in Germany - intoxicating growl at idle, ...(choose a part on the right to read more)
$6,987.20
Make a selection BES99115000S + 11 hp & + 10 tq gain. - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - net weight is 16.4 kg / 36 lbs. (10 lb savings over stock 3.4 l mufflers) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - 90 db maximum (oem muffler is 75 db for reference). - replaces OEM side mufflers and connects to OEM header and catalytic flange. Please note: this muffler does not include exhaust valves and is meant to replace the OEM system on the base 3.4l 991 (2012+). Power is stated at the crank. This is the very 1st aftermarket muffl...(choose a part on the right to read more)
$3,869.80
Make a selection BES99101210SHD For 2012+ 911 (991) with OEM or valved Porsche sport exhaust (pse). Facts: - equal length headers with motorsports merge collector. - 200 cell hd German hjs tri metal sport cats. - 2 3/4 tubing (70mm) - reduces thermal stress on the motor. - made in Germany power with software and bmc filters: - 991 (3.4l) = + 25 crank hp (15 kw) & + 18 crank torque (20 nm) - 991s (3,8l) = + 25 crank hp (15kw) & 18 crank torque (20 nm) our latest development for the 991 is aimed at those who are looking for more torque in the mid range, a rich, deep exhaust growl. These headers contain the latest hjs cats, they are nicknamed "hd" for high durability matrix design catalytic converters. They have a sm-matrix (winding of three f...(choose a part on the right to read more)
$4,834.50
Make a selection 21011125PSE Only for vehicles with Porsche standard sports exhaust system 200 cell, hjs tri-metal, hf (high flow) hjs catalytic cores with "u-torque" design, manufactured by m in Germany. The u-torque design compensates for the backpressure loss while running the high flow cats. The design minimizes the loss of low end torque and adds 10-15 ft-lbs of torque in the mid and top range of the rpms. Why settle for the traditional cross over cat design when you can add more torque in the mid-range and minimize the loss of torque down low where the 997's need it most! Please note: these fit the OEM mufflers and Porsche sport exhaust (pse) mufflers. Tech tip:add one of our installation kits FVD mk 997300
$3,311.00
Make a selection 100211025SSUSA If you have a us model 1980-83 911 SC and are looking to replace your heat exchangers we have some good and bad news. The original heat exchangers (part # 930 211 025 02) are no longer available from Porsche. But, these stainless-steel industries (ssi) heat exchangers will work with modifications. The good news is, once done, you will have more torque and horsepower! Free flow conversion heat exchangers improve sound and performance, while reducing backpressure and thermal load on the motor. These are based off the early style exhausts found on the 1974 2.7 l rs. Those models had a straight through, superior, free flow exhaust design that included a dual inlet muffler. When converting to these heat exchangers y...(choose a part on the right to read more)
$2,863.30
Make a selection 170211013 This steel heat control box is a quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For proper installation, we recommend a new exhaust gasket, part # 91121129700 clamp, part # 90121105122 and connecting piece, part # 91165911900 sold individually. 1 necessary per car.
$140.80
Make a selection 170211015 This stainless-steel heat control box is a quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For proper installation, we recommend a new exhaust gasket, part # 91121129700 clamp, part # 90121105122 and connecting piece, part # 91165911900ssi sold individually. 1 necessary per car.
$177.10
Make a selection BES99722240BES Brombacher 997.2 tt "sport " stainless steel, sport cat converter replacements for our bes- muffler facts: - + 21 crank hp & + 18 crank torque** - 200 cell "hd", tri metal German hjs sport catalysts - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress - 5 on a scale of 1-10 in volume (1 being stock). - reuses OEM v band style connecting hardware. - made in Germany. - available in 100 cell and cat bypass. Please ask your sales person for pricing. - more distinguished growl at idle, partial throttle and wide open throttle. - dme programming not necessary. - reuses OEM ti...(choose a part on the right to read more)
$4,303.20
Make a selection 100211022SSIRE This heat exchanger is engineered for the discerning Porsche 911 owner. Ssi heat exchangers are made from superior t 304 grade (18% cr, 8%+ ni) stainless steel. Ssi has become an industry standard for Porsche 911 heat exchangers due to the exceptional materials, craftsmanship and durability. This is critical when considering heat exchangers, as exhaust leaks caused by poor materials can lead to carbon monoxide entering the cabin via the heating system. Features: t304 stainless steel (18% cr, 8%+ ni) backpressure reduction bolt on replacement reduces the thermal load on the motor sold individually. 1 necessary per car.
$728.20
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |